How to Troubleshoot Noisy Furnace Ducts In Your Home

Troubleshoot Noisy Furnace DuctsDo you have some noisy ductwork this winter? In this blog post, we’ll walk you through a few tips to troubleshoot noisy furnace ducts. But, remember: there’s no substitute to calling in the experts at Reimer!

Furnaces are made to operate without making much noise. However, sometimes certain noises emanate from the furnace area that requires close inspection.

If you hear strange noises coming from the furnace area, it’s possible that something is wrong with the system.

Noises can come from either the furnace or the ducts. In both the situations, it is recommended to contact a professional furnace repair technician to get the system checked. In this article, we will take a look at some of the probable causes for noise coming from the duct.

Identifying noisy furnace duct sounds

Here are some of the common duct noises and some of the probable reasons of the noise.

Popping and Banging Noise – The sound of popping and banging is usually caused by the expansion and contrition of the duct walls due to temperature changes.

Rattling Noise – The rattling noise is most often caused by loose metal ducts that tend to knock against one another. The sealing starts to fails as ducts age due to which the duct connection tend to wiggle and get loose from the static pressure.

Vibrating or Shaking Noise – A sound of vibrating or shacking of the duct walls normally occurs due to the blockage of the return side airflow. This usually happens due to a clogged filer that results in drop in the air pressure that makes the duct walls to vibrate and shake.

Booming Noise – A loud booming noise coming from the duct emanates from the place where the duct trucks is connected with the plenum. The connection tends to endure the greatest swings in temperature. Inadequate expansion of joints or dampers contributes to the noise due to which you can hear a large boom echoing through the supply ducts.

Whistling or rumbling noise – In some cases, you can hear whistling or rumbling noise emanating from the ductwork. The whistling noise is normally caused due to excessive air flow through the ducts. On the other hand, the rumbling noise results due to pressure differences between the supply and the return ducts.


A professional furnace technician can perform a thorough check to identify the exact source of the noise. Different noises require different remedies. To better isolate and resolve the noise, you should consider requesting the technician to install a flexible transition for a furnace to quiet the noise coming from the duct.

Generally, noises coming from the ducts do not represent a major fault with the furnace. Apart from being a slight inconvenience, they don’t generally represent a serious issue with the furnace. However, if you hear strange noise emanating from the furnace itself, it’s essential that you have it checked by a professional technician.

Call Reimer for noisy furnace duct inspections, and for furnace repair

Make sure that you hire an experienced and licensed furnace technician. An experienced technician will expertly identify and resolve all kinds of furnace problems due to which you can spend the entire winter months in total comfortable and warmth.

If you want to hire experienced and NATE-certified furnace repair technicians in Western New York, you can contact Reimer Home Services.

Here’s How To Prevent A Clogged Kitchen Drain

Clogged Kitchen DrainA clogged kitchen drain can be a nuisance for anyone. Dealing with a clogged drain can be time-consuming, and the smell that comes from a clogged system adds to the inconvenience of having to deal with a backed up system.

Fortunately, you can avoid clogged drains by taking a few simple steps. In this article, we will share 5 simple steps that you can take to prevent kitchen drains from becoming clogged thereby saving on plumbing costs.

If you do have a clogged kitchen drain, contact the team at Reimer for drain cleaning service.

1. A few things you should never pour down the sink

In order to avoid clogged drains, you should never pour certain substances down the sink. Some of the items that you should avoid pouring down the sink include coffee grounds, cooking oil, and fats trimmed off meat. These substances tend to accumulate in the pipes, leading to blockage.

Also, you should never pour setting-type joint compounds down the sink as they harden up upon contact with water. If you pour the compound down the drain, you will be in for a rock-solid clog. Sand is another building element that you should never pour down the drain. The sand can settle down the drain that is difficult to remove.

2. Use a sink strainer

Consider using sink strainer over the drain. The strainer can catch food particles and other substances that can’t wash down the drain. This will greatly reduce the chances of a clogged kitchen drain. Just remember to empty the strainer when it becomes full.

3. Pour hot / cold water down the drain

You can pour boiling kettle water down the drain at least once week to melt away fat and grease that may have collected inside the pipes. Make sure that you pour the hot water slowly to avoid splashing.

If you have garbage disposal installed, you should consider running a stream of cold faucet water while using the disposal. This will carry the waste material through the drainage system.

4. Use baking soda to clean the drain

To clean the drain, it’s recommended that you throw a handful of baking soda followed by hot water down the drain. Baking soda can not only clean the pipe of accumulated waste but also absorb foul smells.

5. Use a stopper once a week

In case your kitchen has a stopper, you should fill the sink once a week by closing the stopper. When you release the stopper, the force of the water flow will flush substances that stick to the pipe. If you don’t have a stopper in the sink, pouring boiling water can do the same trick.

Call Reimer for help clearing a clogged kitchen drain

In case you have any plumbing problem in the area of Buffalo, you can contact Reimer Home Services with confidence. Our licensed, trained and expert plumbers can solve all kinds of drain problems including a clogged kitchen drain.

Here’s How To Avoid Premature Furnace Heat Exchanger Failure

furnace heat exchanger failureIf your furnace is getting up there in age, you’re at risk of a furnace heat exchanger failure

What is the heat exchanger?

The heat exchanger is a critical part of the furnace that must be kept in good working order to avoid costly maintenance and emergency furnace breakdown. Any defect with the exchanger can lead to a major defect requiring repair or replacement. That’s why it’s essential that you have the device checked and cleaned by a professional furnace repair technician.

The heat exchanger plays an important role in generating warm air. Understanding the common reasons of heat exchange failure is important if you want to avoid emergency breakdowns. Here are some of the essential tips to prevent irreversible damage to the heat exchanger.  And this is important as the total cost of replacing the exchanger can be as much as $1,200.

How to avoid a premature breakdown of the heat exchanger

The heat exchanger should be properly inspected at regular intervals.  The major fault that develops with the heat exchanger is the development of a crack or hole inside. The constant cooling and heating result in a crack to develop inside the exchanger.

With proper maintenance and service, the heat exchangers can last for a long period of time. A professional technician can identify problems and perform the necessary furnace repair works that ensures that major fault does not develop with the heat exchanger.

The main thing that results in cracks to develop inside the heat exchanger is reduced airflow due to dirty filters. The filters need to be kept clean of dirt, dust, and other debris. Clogged filters reduce the air flow that result in development of cracks inside the system.

Other reasons for reduced air flow are the dirty fan blades, dirty duct work, and obstructed air vents. All of these factors can cause major damage to the heat exchanger. Also, the air obstructions can make the system strain in generating the heat that may result in overheating problem.

That being said, most modern furnaces have protection system that turns down the heater when the temperature becomes unusually high. However, this cannot prevent serious damage to the internal components thereby requiring costly repairs.

Schedule an annual furnace tune-up with Reimer

Annual furnace maintenance is the best way to avoid premature furnace heat exchanger failure. During the routine inspection, a qualified technician will ensure that the system is working properly without any kind of air obstructions. In case an aberration is found within the system, the technician will perform the repairs right away.

The cost of the annual furnace maintenance is generally not that much. This is especially the case when you consider that you will be saving a lot in the long run due to lower repair costs, reduced heating bills, and less frequent furnace replacement.

Furnace heat exchanger failure? Call the experts at Reimer!

Apart from that, the peace of mind due to not having to go through unplanned, emergency repairs of the furnace makes annual furnace maintenance more than worth it in the end. If you want help of qualified furnace repair technicians in Western New York, you should contact Reimer Home Services.